Simulate the real exam

We provide different versions of 642-813 practice exam materials for our customers, among which the software version can stimulate the real exam for you but it only can be used in the windows operation system. It tries to simulate the 642-813 best questions for our customers to learn and test at the same time and it has been proved to be good environment for IT workers to find deficiencies of their knowledge in the course of stimulation.

After purchase, Instant Download: Upon successful payment, Our systems will automatically send the product you have purchased to your mailbox by email. (If not received within 12 hours, please contact us. Note: don't forget to check your spam.)

There is no doubt that the IT examination plays an essential role in the IT field. On the one hand, there is no denying that the 642-813 practice exam materials provides us with a convenient and efficient way to measure IT workers' knowledge and ability(642-813 best questions). On the other hand, up to now, no other methods have been discovered to replace the examination. That is to say, the IT examination is still regarded as the only reliable and feasible method which we can take (642-813 certification training), and other methods are too time- consuming and therefore they are infeasible, thus it is inevitable for IT workers to take part in the IT exam. However, how to pass the Cisco 642-813 exam has become a big challenge for many people and if you are one of those who are worried, congratulations, you have clicked into the right place--642-813 practice exam materials. Our company is committed to help you pass exam and get the IT certification easily. Our company has carried out cooperation with a lot of top IT experts in many countries to compile the 642-813 best questions for IT workers and our exam preparation are famous for their high quality and favorable prices. The shining points of our 642-813 certification training files are as follows.

Only need to practice for 20 to 30 hours

You will get to know the valuable exam tips and the latest question types in our 642-813 certification training files, and there are special explanations for some difficult questions, which can help you to have a better understanding of the difficult questions. All of the questions we listed in our 642-813 practice exam materials are the key points for the IT exam, and there is no doubt that you can practice all of 642-813 best questions within 20 to 30 hours, even though the time you spend on it is very short, however the contents you have practiced are the quintessence for the IT exam. And of course, if you still have any misgivings, you can practice our 642-813 certification training files again and again, which may help you to get the highest score in the IT exam.

Fast delivery in 5 to 10 minutes after payment

Our company knows that time is precious especially for those who are preparing for Cisco 642-813 exam, just like the old saying goes "Time flies like an arrow, and time lost never returns." We have tried our best to provide our customers the fastest delivery. We can ensure you that you will receive our 642-813 practice exam materials within 5 to 10 minutes after payment, this marks the fastest delivery speed in this field. Therefore, you will have more time to prepare for the 642-813 actual exam. Our operation system will send the 642-813 best questions to the e-mail address you used for payment, and all you need to do is just waiting for a while then check your mailbox.

Cisco Implementing Cisco IP Switched Networks Sample Questions:

1. What is the effect of configuring the following command on a switch?
Switch(config) # spanning-tree portfast bpdufilter default

A) If BPDUs are received by a port configured for PortFast, then PortFast is disabled and the BPDUs are processed normally.
B) The command enables BPDU filtering on all ports regardless of whether they are configured for BPDU filtering at the interface level.
C) If BPDUs are received by a port configured for PortFast, they are ignored and none are sent.
D) If BPDUs are received by a port configured for PortFast, the port transitions to the forwarding state.

2. Refer to the exhibit.

The network operations center has received a call stating that users in VLAN 107 are unable to access resources through router 1. What is the cause of this problem?

A) VLAN 107 does not exist on switch
B) Spanning tree is not enabled on VLAN 107.
C) VTP is pruning VLAN 107.
D) VLAN 107 is not configured on the trunk.

3. What is the result of entering the command port-channel load-balance src-dst-ip on an EtherChannel link?

A) Packets are distributed across the access ports in the channel based first on the source IP address and then on the destination IP addresses.
B) Packets are distributed across the ports in the channel based on the source and destination MAC addresses.
C) Packets are balanced across the ports in the channel based first on the source MAC address, then on the destination MAC address, then on the IP address.
D) Packets are distributed across the ports in the channel based on both the source and destination IP addresses.

4. Refer to the exhibit.

Which two sets of procedures are best practices for Layer 2 and 3 failover alignment? (Choose two.)

A) Configure the D-SW1 switch as the active HSRP router and the STP root for VLANs 11 and
110. Configure the D-SW2 switch as the active HSRP router and the STP root for VLANs 12 and
120.
B) Configure the D-SW1 switch as the active HSRP router and the backup STP root for VLANs 11 and 110. Configure the D-SW2 switch as the active HSRP router and the backup STP root for VLANs 12 and 120.
C) Configure the D-SW1 switch as the active HSRP router and the STP root for all VLANs. Configure the D-SW2 switch as the standby HSRP router and backup STP root for all VLANs.
D) Configure the D-SW2 switch as the active HSRP router and the STP root for all VLANs. Configure the D-SW1 switch as the standby HSRP router and backup STP root for all VLANs.
E) Configure the D-SW1 switch as the standby HSRP router and the backup STP root for VLANs 12 and 120. Configure the D-SW2 switch as the standby HSRP router and the backup STP root for VLANs 11 and 110.
F) Configure the D-SW1 switch as the standby HSRP router and the STP root for VLANs 11 and
110. Configure the D-SW2 switch as the standby HSRP router and the STP root for VLANs 12 and
120.

5. What are three possible router states of HSRP routers on a LAN? (Choose three.)

A) established
B) idle
C) initial
D) active
E) backup
F) standby

Solutions: